Most of our residential work is in London and the city shapes how we work. A Georgian stairwell, a Victorian chimney breast and a plasterboard wall in a new-build tower all take Venetian plaster, but they need different preparation underneath it. Concierge hours, service lifts booked by the half day, parking permits and a programme shared with other trades are part of the job too. We plan around all of it before a trowel is lifted and every finish is signed off on a physical sample panel in your own room first.
Request a London quote→See Venetian plaster in detail →
Venetian plaster, as we install it
What we apply is lime putty carrying graded marble powder, not an acrylic look-alike. It goes on in three thin coats, the last pressed in wet so the marble grain sits inside the surface rather than on top of it, then compressed with a steel trowel to one of three levels:
- Honed - a soft matt stone surface with visible trowel movement. The most forgiving where the light is low or the walls are old.
- Satin - compressed hard on the final pass for a low sheen that shifts as you walk past. The usual choice for principal rooms.
- Burnished - extra passes of the trowel to a near-mirror. Dramatic in a hallway or stairwell and the least forgiving of what is underneath.
Because it is lime, it stays vapour-open. That matters in London more than almost anywhere, because so much of the housing stock has solid walls that need to let moisture out. Marmorino, the textured matt member of the same family, suits the same rooms; Marmorino vs Venetian plaster explains how to choose between them.
London buildings and what they need underneath
The finish is under two millimetres thick, so it reads every undulation behind it. Most of a London job is getting the wall right first and that depends on when the building went up.
Georgian and Regency townhouses. Solid brick walls, original lime plaster, tall rooms and deep cornices. These walls need to breathe, so the preparation has to be lime-compatible as well as the finish. High stairwells mean towers and slower working and cut-in around cornices and window reveals is done by hand.
Victorian and Edwardian houses. Solid walls again, often patched with gypsum over the years, so one room can hold three different substrates. Chimney breasts, lath-and-plaster ceilings and half-basements each need assessing on their own. We find out what is there at survey rather than on day one.
Mansion blocks. Usually solid walls behind a later skim. The building itself sets the rules: working hours, noise, lift bookings, where materials can be stored and how long a van can stand outside. We get the management company's requirements before we price.
New-build and lateral apartments. Plasterboard and fresh skim. The risks here are board joints that move and new plaster that is not yet dry, so we check moisture and detail the joints before any decorative coat goes on. Where the programme is tight, we will tell you if the walls are not ready rather than apply over them.
Basements. A tanked or membrane-lined wall cannot breathe whatever goes over it, so the finish has to suit the waterproofing system behind it. We coordinate with the basement contractor rather than guess.
For more on this, read Venetian plaster in London homes and Lime plaster for period homes.
Working in London
The finish does not change between a Zone 1 flat and a house with a driveway, but the job does and we would rather be open about it.
- Access and parking. Controlled parking zones, suspended bays, congestion and emission charges and loading restrictions all affect how a team gets to site each day. A permit or bay you arrange in advance costs less than us solving it daily.
- Building rules. Concierge hours, booked service lifts and quiet periods in mansion blocks and managed buildings are built into the programme from the start.
- Other trades. These are wet, multi-coat finishes with cure time between coats. The job runs best when we have the room to ourselves for consecutive days; where the programme needs phased or out-of-hours working, we price it that way from the start.
- Listed interiors. If your home is listed, check with your local authority's conservation officer before changing historic plaster, as consent may be needed. Lime is usually the material they want to see.
What sets the price of Venetian plaster →
Where we work in London
Every borough. Areas we cover include:
- Central: Mayfair, Marylebone, Fitzrovia, Bloomsbury, Holborn, Covent Garden, the City
- West: Belgravia, Chelsea, Kensington, Notting Hill, Holland Park, Fulham, Chiswick, Richmond
- North: Hampstead, Highgate, Primrose Hill, Islington, Crouch End, Muswell Hill
- East: Shoreditch, Hackney, Clerkenwell, Canary Wharf, Wapping
- South: Battersea, Clapham, Wandsworth, Wimbledon, Dulwich, Greenwich, Blackheath, Bromley, Chislehurst
Our studio and sample library is in Holborn, so a site visit anywhere in the capital is a short journey rather than a day.
See it before you choose
Venetian plaster never looks the same on a screen as it does on a wall. Visit the studio in Holborn by appointment to see the polish levels and colours in the hand, or try them first in the visualiser. Before we start, we make a physical sample panel in the room it is going into, in your light and that panel is what we work to.
Request a London quote→
Also in London: microcement and other mineral finishes
Alongside Venetian plaster we install microcement across London: grout-free bathrooms and wet rooms, floors over screed or existing tile and kitchens with worktops, splashbacks and cabinetry in one surface. For wet zones we often pair the two, with Venetian plaster on the walls and tadelakt or microcement where the water runs.